54" x 9.00" x 40,000# Loopco Slitting Line

Brand
LOOPCO

Model

Stock #
2059

Condition
Used

Year

Location
Toledo, Ohio
United States

Specifications

Max Width of Workpiece 54 inches
Max Thickness of Workpiece (in.) 0.250 inches

Equipped With

 
Capacity: 0.010" - 0.250" Mild Steel
Coil Weight: 40,000#
Line Direction: Right to Left
 
Consisting of:
 
-Entry Coil Car: Revolvator
  40,000# Capacity
  60" wide Bed
  72" O.D. Capacity
  (2) - 5" bore hydraulic lift cylinders
  Lift: Approx. 16"
  Self-contained hydraulics
    3 HP AC motor
  Each axle individually driven by hyd. motors
  Pushbutton control
  Approx. 12" from floor to bottom of "V" cradle
  Removable 5" high riser on bed
  Overall size: 90" L x 64" W x 89" High
 
-Uncoiler:
  20" - 24" I.D.
  Hydraulic Expansion
  Pumpkin Tooth Mandrel
  54.5" Face Mandrel
  Powered Holddown Roll w/Rubber Covered Roll
  AC Motor Threading Drive w/Air Clutch
  Sliding Base
  Wichita Water Cooled Brake
  Water Cooler for Brake
  Passline: 40" from Floor to Center of Mandrel
  Overall Size: 150" L x 74" W x 93" High
 
-Entry Unit:
  Threading Table
  Pinch Rolls, 8" Dia. x 56.5" Face Rolls, Idler Type
  Side Guides, Manual Adj.
  Passline: 47"
  Overall Size: 84" L x 50" W x 75" High
 
-Crop Shear:
  58" Long Blade
  Hydra-Mechanical Upcut Type
  10" Bore Hydraulic Cylinder
  Entry Passline Roll
  Spring Loaded Holddown
  Passline: 49"
  Overall Size: 109" L x 35" W x 81" High
 
-Flattener:
  SO#: 6625
  5 Work Rolls, 2 over 3
    6" Dia. x 60" Face Rolls
  Entry Passline Roll, 8" Dia. x 60" Face
  Entry Driven Pinch Rolls, 6" Dia. x 60" Face
  Individual Jackscrew Adjustment of Top Rolls by AC Motors
  15 HP AC Gearmotor Drive, 1750 RPM, 230/460 V
    Foote Jones Reducer w/38.4:1 Ratio
    Air Clutch
  Passline: 48"
  Overall Size: 151" L x 70" W x 85" High
                19,000 Lbs.
 
-(2) Slitter Heads:
  Crane Type Removable Heads
  Single Eccentric Arbor Adjustment
  (1) - 9" Dia. x 55" Face Arbors
     Entry Table
  (1) - 6" Dia. x 55" Face Arbors
     Entry Side Guides, Manual Adj.
     Entry Passline Rolls, 4" Dia. x 59.75" Long
  75 HP DC Motor, 500/2000 RPM, 500 V, w/Blower
  30 HP AC Motor Threading Drive, 1760 RPM, 230/460 V
  Alten Reducer w/1.837:1 Ratio
  Overall Size: 9" Head: 128" L x 57" W x 81" High, 15,000 Lbs.
                6" Head: 122" L x 50" W x 69" High, 10,000 Lbs.
                Drive: 150" L x 46" W x 47" High, 7,500 Lbs.
 
-(2) Scrap Winders:
  Approx. 25" W x 26" Dia. Scrap Ball Capacity
  Hydraulic Motor Driven
  Self-Contained Hydraulic Power Unit
    15 HP AC Motor, 1760 RPM, 230/460V
  Overall Size: 84" L x 52" W x 49" High (Each Winder)
 
-Pit Cross Over Table:
 
-Tension Stand:
  Drag Board Type w/(3) Air Cylinders for Clamping Pressure
  Entry Separator Tooling Bar, 54" Long
  Entry Passline Roll
  60" Long Pads
  Exit Passline Roll w/Encoder
  Passline: 58.5"
  Overall Size: 94" L x 43" W x 79" High
 
-Free Standing Overarm Separator:
  Deflector Roll
  Threading Table to Recoiler
 
-Recoiler:
  16" Dia. x 58" Face Drum
  20" Dia. Bolt On Pads
  22" Dia. x 57" Face Drum
  Hydraulic Clamp and Expansion
  12" Dia. Main Shaft
  Hydraulic Pushoff
  Lufkin (2) Speed Gear Box w/10.6:1 and 31.7:1 Ratios
  200 HP DC Motor, 500/2000 RPM, 500 V w/Blower
  Air Operated Holding Brake
  Passline: 40" from Floor to Center of Drum
  Overall Size: 180" L x 102" W x 92" High
 
-Hydraulic Power Unit:
 
-Electrical Panel: Eurotherm DC Drive:
 
-Misc. Tooling Included.