48" x 0.050" Strilich Coil Cut to Length Line

Brand
Not Specified

Model

Stock #
1206

Condition
Used

Year

Location
City Not Specified,

Specifications

Equipped With


STRILICH "PANTHER" CUT TO LENGTH LINE

COIL WIDTH: 24" - 48"

MATERIAL TYPE: ELECTRO-GALVANIZED, CR, PREPAINTED MATERIAL THICKNESS: 0.027" - 0.050"

LENGTH ACCURACY: +/- 0.030"

LINE SPEED: 75 FPM

MAXIMUM ROLL SPEED (125 MAX @ 0.048"

MATERIAL THICKNESS)

SHEAR CUTS: 25 CUTS MAXIMUM @ 18" FEED LENGTH SLIT CUT CAPACITY: 5 CUTS OF .050" MODE OF OPERATION: SINGLE EDGE OPERATION, FEED TO STOP ELECTRICALS: 480 V / 3 PH / 60 HZ. CONSISTING OF THE FOLLOWING: -LESS UNCOILER (CAN BE PROVIDED AT EXTRA COST) -ADJUSTABLE ENTRY GUIDE: MAXIMUM MATERIAL WIDTH: 48" FOUR (4) SIDED HARDENED PLATE TYPE ENTRY GUIDES ONE SIDE IS FIXED WITH THE OTHER SIDE BEING ADJUSTED THROUGH HANDWHEEL ENTRY CATENARY SECTION FOR MATERIAL LOOP SUPPORT ENTRY GUIDE AND CATENARY ROLL OUT OF THE WAY TO SET UP THE SLITTER -QUICKSET SLITTER: 4" DIAMETER ARBORS x 48" WIDE ARBORS MOUNTED IN HEAVY DUTY TAPERED ROLLER BEARINGS DRIVEN THROUGH COMMON DRIVE WITH STRAIGHTENER ADJUSTABLE OUTBOARD SQUARING GUIDE - MANUAL ADJUSTMENT 5 SETS 46SK D-2 MATERIAL SLITTER KNIVES 5 SETS 46RS RUBBER STRIPPER RINGS -STRAIGHTENER: MAXIMUM STRIP WIDTH CAPACITY: 48" MATERIAL THICKNESS CAPACITY: 0.050" 30 HP VARIABLE SPEED AC VECTOR DRIVE GEARED FOR 75 MAX. ROLL SPEED 5 WORK ROLLS (2 OVER 3) - 3" DIAMETER HARDENED AND GROUND POWERED 4" DIAMETER AIR LOADED ENTRY PINCH ROLLS ALL WORK ROLLS AND PINCH ROLLS ARE CHAIN DRIVEN CENTRALIZED MANUAL GREASE POINTS PROVIDED FOR WORK ROLL AND PINCH ROLL BEARING LUBRICATION. END HOUSINGS AND BEARING BLOCKS TO BE HEAVY DUTY MACHINED STEEL HEAVY DUTY WELDED STRUCTURAL STEEL FRAMEWORK TOP WORK ROLL HEAD VERTICAL AND BANK ADJUSTABLE VIA (4) ANTI-BACKLASH SCREWJACKS. AUTOMATIC NON-CONTACT LOOP CONTROL AUTOMATICALLY CONTROLS SPEEDS OF MATERIAL THROUGH STRAIGHTENER. -ELECTRONIC DIGITAL LENGTH CONTROL MEASURING SYSTEM: PROGRAMMABLE CONTROLLER WITH BUILT-IN BATCH COUNTER AND RATE MULTIPLIER MAIN OPERATOR CONTROL CONSOLE HEAVY DUTY ENCODER MOUNT -HYDRAULIC CUTOFF SHEAR: MAXIMUM STRIP WIDTH CAPACITY: 48" MATERIAL THICKNESS CAPACITY: 0.050" CUTS PER MINUTE: 25 MAXIMUM STROKE PER MINUTE: 60 MAXIMUM HYDRAULIC ACTUATED CUTOFF DIE COMPLETE WITH (4) SIDED D2 HC-HC CUTOFF BLADES -COMMON SUPPORT BASE: HEAVY-DUTY WELDED STRUCTURAL STEEL BASE CONTAINING THE ENTRY GUIDE, SLITTER, STRAIGHTENER AND SHEAR, FOR QUICK AND ACCURATE INSTALLATION. NO FOUNDATION WORK REQUIRED. -TRANSFER BELT CONVEYOR: MAXIMUM SHEET WIDTH: 48" TRANSFERS SHEETS OR STRIPS FROM SHEAR FULL WIDTH ENDLESS TYPE BELT QUICK AND SIMPLE BELT ALIGNMENT ADJUSTMENT 2" DIAMETER CONVEYOR DRUMS 48" LONG BED SECTION ALLOWS LIFT TABLE TO FIT UNDER CONVEYOR FOR EASY OPERATOR STACKING. VARIABLE SPEED DRIVE -HYDRAULIC POWERED LIFT TABLE: MAXIMUM BUNDLE WEIGHT: 2,500 LBS. MAXIMUM WIDTH CAPACITY: 48" MAXIMUM LENGTH CAPACITY: 48" SELF CONTAINED HYDRAULIC PUMPING UNIT HEAVY DUTY DESIGN POWERED ROLLER TYPE CONVEYOR TO BE MOUNTED ON LIFT TABLE DECK FOR END DISCHARGE OF STACKED MATERIAL. LIFT TABLE TO BE MOUNTED ON CASTERS AND ON STEEL TRACK AND IS MANUALLY MOVED IN AND OUT FROM UNDER CONVEYOR FOR STACKING OF MATERIAL. -CONTROLS: FULLY INTEGRATED OPERATOR CONTROL CONSOLE FOR COMPLETE LINE OPERATION. ALL ELECTRICAL, HYDRAULIC AND PNEUMATIC CONTROLS SUPPLIED. -CLEANED, WIRED AND TESTED